draft-allan-l2vpn-spbm-evpn-03:
802.1aq and 802.1Qbp Support over EVPN
Author(s): Don Fedyk, Jeff Tantsura, David Allan, Ali Sajassi
This document describes how Ethernet Shortest Path Bridging MAC mode (802.1aq) and (802.1Qbp) can be combined with EVPN in a way that interworks with PBB-PEs as described in the PBB-EVPN solution in a way that permits operational isolation...
L2VPN Working Group Dave Allan, Jeff Tantsura
Internet Draft Ericsson
Intended status: Standards Track Don Fedyk
Expires: August 2013 Alcatel-Lucent
Ali Sajassi
Cisco
February 2013
802.1aq and 802.1Qbp Support over EVPN
draft-allan-l2vpn-spbm-evpn-03
Abstract
This document describes how Ethernet Shortest Path Bridging MAC mode
(802.1aq) and (802.1Qbp) can be combined with EVPN in a way that
interworks with PBB-PEs as described in the PBB-EVPN solution in a
way that permits operational isolation of each Ethernet network
subtending an EVPN core while supporting full interworking between
the 3 variations of Ethernet operation.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance
with the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet
Engineering Task Force (IETF), its areas, and its working
groups. Note that other groups may also distribute working
documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-
Drafts as reference material or to cite them other than as "work
in progress".
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on August 2013.
Copyright and License Notice
Allan et al., Expires August 2013 [Page 1]
Internet-Draft draft-allan-l2vpn-spbm-evpn-03 February 2013
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with
respect to this document. Code Components extracted from this
document must include Simplified BSD License text as described
in Section 4.e of the Trust Legal Provisions and are provided
without warranty as described in the Simplified BSD License.
Table of Contents
1. Introduction...................................................3
1.1. Authors......................................................3
1.2. Requirements Language........................................3
2. Conventions used in this document..............................3
2.1. Terminology..................................................3
3. Changes since previous version.................................4
4. Solution Overview..............................................4
5. Elements of Procedure..........................................5
5.1. PE Configuration.............................................5
5.2. DF Election..................................................6
5.3. Control plane interworking ISIS-SPB to EVPN..................6
5.4. Control plane interworking EVPN to ISIS-SPB..................6
5.5. Data plane Interworking 802.1aq SPBM island or PBB-PE to
EVPN..............................................................8
5.6. Data plane Interworking EVPN to 802.1aq SPBM island..........8
5.7. Data plane interworking EVPN to 802.1ah PBB-PE...............8
5.8. Dataplane interworking between 802.1Qbp islands and EVPN.....8
5.9. Multicast Stitching..........................................8
6. Other Aspects..................................................8
6.1. Flow Ordering................................................8
6.2. Transit......................................................9
7. Acknowledgements...............................................9
8. Security Considerations........................................9
9. IANA Considerations............................................9
10. References....................................................9
10.1. Normative References........................................9
10.2. Informative References......................................9
11. Authors' Addresses...........................................10
Allan et al., Expires August 2013 [Page 2]
Internet-Draft draft-allan-l2vpn-spbm-evpn-03 February 2013
1. Introduction
This document describes how Ethernet Shortest Path Bridging MAC mode
(802.1aq) and (802.1Qbp) along with PBB-PEs and PBBNs (802.1ah) can
be supported by EVPN such that each island is operationally isolated
while providing full L2 connectivity between them. Each island can
use its own control plane instance and multi-pathing design, be it
multiple ECT sets, multiple spanning trees, or ECMP.
The intention is to permit both past, current and emerging future
versions of Ethernet to be seamlessly integrated to permit large
scale, geographically diverse numbers of Ethernet end systems to be
fully supported with EVPN as the unifying agent.
1.1. Authors
David Allan, Jeff Tantsura, Don Fedyk, Ali Sajassi
1.2. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC2119 [1].
2. Conventions used in this document
2.1. Terminology
BCB: Backbone Core Bridge
BEB: Backbone Edge Bridge
BU: Broadcast/Unknown
B-MAC: Backbone MAC Address
B-VID: Backbone VLAN ID
CE: Customer Edge
C-MAC: Customer/Client MAC Address
DF: Designated Forwarder
ESI: Ethernet segment identifier
EVPN: Ethernet VPN
ISIS-SPB: IS-IS as extended for SPB
I-SID: I-Component Service ID
MP2MP: Multipoint to Multipoint
Allan et al., Expires August 2013 [Page 3]
Internet-Draft draft-allan-l2vpn-spbm-evpn-03 February 2013
MVPN: Multicast VPN
NLRI: Network layer reachability information
PBBN: Provider Backbone Bridged Network
PBB-PE: Co located BEB and PE
PE: provider edge
P2MP: Point to Multipoint
P2P: Point to Point
RD: Route Distinguisher
SPB: Shortest path bridging
SPBM: Shortest path bridging MAC mode
3. Changes since previous version
1) Reverting to NLRI encoding aligned with the PBB-EVPN draft.
4. Solution Overview
The EPVN solution for 802.1aq SPBM incorporates control plane
interworking in the PE to map ISIS-SPB [2] information elements into the
EVPN NLRI information and vice versa. This requires each PE to act both
as an EVPN BGP speaker and as an ISIS-SPB edge node. Associated with
this are procedures for configuring the forwarding operations of the PE
such that an arbitrary number of EVPN subtending SPB islands may be
interconnected without any topological or multipathing dependencies.
This requires each PE connected to an SPBM island to act both as an EVPN
BGP speaker and as an ISIS-SPB edge node. This model also permits PBB-
PEs as defined in draft-l2vpn-pbb-evpn-02[6] to be seamlessly
communicate with the SPB islands. The next version of this document will
add support for 802.1Qbp permitting seamless interworking between
802.1ah, 802.1aq and 802.1Qbp as well as supporting subtending 802.1ad
based PBNs.
+--------------+
| |
| |
+-----+ +----+ | | +----+ +---+
| |-----|SPBM| | | |PBB |---|CE2|
|SPBM | |PE1 | | IP/MPLS | |PE1 | +---+
+---+ |NTWK1| +----+ | Network | +----+
Allan et al., Expires August 2013 [Page 4]
Internet-Draft draft-allan-l2vpn-spbm-evpn-03 February 2013
|CE1|-| | | |
+---+ | | +----+ | |
| |-----|SPBM| | | +----+ +-----+
+-----+ |PE2 | | | |SPBM| |SPBM | +---+
+----+ | | |PE3 |---|NTWK2|-|CE3|
+--------------+ +----+ +-----+ +---+
Figure 1: PBB and SPBM EVPN Network
Each EVPN is identified by a route target. The route target identifies
the set of SPB islands and BEB-PEs that are allowed to communicate. This
manifests itself as a set of Ethernet segments, where each Ethernet
segment ID is unique within the route target.
BGP acts as a common repository of the I-SID attachment points for the
set of subtending PEs/SPBM islands. This is in the form of B-MAC
address/I-SID/Tx-Rx-attribute tuples. BGP filters leaking I-SID
information into each SPBM ISLAND on the basis of locally registered
interest. If an SPBM ISLAND has no BEBs registering interest in an I-
SID, information about that I-SID from other SPBM island, PBB-PEs or
PBBNs will not be leaked into the local ISIS-SPB routing system.
Each SPBM island is administered to have an associated Ethernet Segment
ID (ESI) associated with it.
For each B-VID in an SPBM island, a single SPBM-PE is elected the
designated forwarder for the B-VID. An SPBM-PE may be a DF for more than
one B-VID. This is described further in section 4.2. The SPBM-PE
originates IS-IS advertisements as if it were an I-BEB or IB-BEB that
proxy for the other SPBM islands and PBB PEs in the VPN defined by the
route target, but the PE typically will not actually host any I-
components.
An SPBM-PE that is a DF for a B-VID strips the B-VID tag information
from frames relayed towards the EVPN. The DF also inserts the
appropriate B-VID tag information into frames relayed towards the SPBM
island on the basis of the local I-SID/B-VID bindings advertised in
ISIS-SPB.
5. Elements of Procedure
5.1. PE Configuration
At SPBM island commissioning a PE is configured with:
Allan et al., Expires August 2013 [Page 5]
Internet-Draft draft-allan-l2vpn-spbm-evpn-03 February 2013
1) The route target for the service instance. Where a service
instance is defined as the set of SPBM islands, PBBNs and PBB-PEs
to be interconnected by the EVPN.
2) The unique ESI for the SPBM island. Mechanisms for deriving a
common ESI for the SPBM island are for a future version of the
document.
And the following is configured as part of commissioning an ISIS-SPB
node:
1) A Shortest Path Source ID (SPSourceID) used for algorithmic
construction of multicast DA addresses. Note this is required for
SPBM BEBs independent of the EVPN operation.
2) The set of VLANs (identified by B-VIDs Ethernet frames) used in
the SPBM island and multipathing algorithm IDs to use. The B-VID
may be different in different domains and may be removed as
carried over the IP/MPLS network.
A type-1 RD for the node can be auto-derived. This will be described
in a future version of the document.
5.2. DF Election
PEs self appoint in the role of DF for a B-VID for a given SPBM
island. The procedure used is as per section 9.5.2 of draft-ietf-
l2vpn-evpn-01[4] "DF election with service carving".
5.3. Control plane interworking ISIS-SPB to EVPN
When a PE receives an SPBM service identifier and unicast address
sub-TLV as part of an ISIS-SPB MT capability TLV it checks if it is
the DF for the B-VID in the sub-TLV.
If it is the DF, and there is new or changed information then a MAC
advertisement route NLRI is created for each new I-SID in the sub-
TLV.
- the Route Distinguisher (RD) is set to that of the PE
- the ESI is that of the SPBM ISLAND
- the Ethernet tag ID contains the I-SID (including the Tx/Rx
attributes). The encoding of I-SID information is as per figure 2.
Allan et al., Expires August 2013 [Page 6]
Internet-Draft draft-allan-l2vpn-spbm-evpn-03 February 2013
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|T|R| Reserved | I-SID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2: I-SID encoding in the Ethernet tag-ID field
- the MAC address from the sub-TLV
- an MPLS label
Similarly in the scenario where a PE became elected DF for a B-VID in
an operating network, the IS-IS database would be processed in order
to construct the NLRI information associated with the new role of the
PE.
If the BGP database has NLRI information for the I-SID, and this is
the first instance of registration of interest in the I-SID from the
SPB island, the NLRI information with that tag is processed to
construct an updated set of SPBM service identifier and unicast
address sub-TLVs to be advertised by the PE.
The ISIS-SPB information is also used to keep current a local table
indexed by I-SID to indicate the associated B-VID for processing of
fraPE received from EVPN. When an I-SID is associated with more than
one B-VID, only one entry is allowed in the table. Rules for this
will be in a future version of the document.
5.4. Control plane interworking EVPN to ISIS-SPB
When a PE receives a BGP NLRI that is new information, it checks if
the I-SID in the Ethernet Tag ID locally maps to the B-VID it is an
elected DF for. Note that if no BEBs in the SPB island have
advertised any interest in the I-SID, it will not be associated with
any B-VID locally, and therefore not of interest. If the I-SID is of
local interest to the SPBM island and the PE is the DF for the B-VID
that that I-SID is locally mapped to, a SPBM service identifier and
unicast address sub-TLV is constructed/updated for advertisement into
IS-IS.
The NLRI information advertised into ISIS-SPB is also used to locally
populate a forwarding table indexed by B-MAC/I-SID that points to the
Allan et al., Expires August 2013 [Page 7]
Internet-Draft draft-allan-l2vpn-spbm-evpn-03 February 2013
label stack to impose on the SPBM frame. The bottom label being that
offered in the NLRI.
5.5. Data plane Interworking 802.1aq SPBM island or PBB-PE to EVPN
When an PE receives a frame from the SPBM island in a B-VID for which
it is a DF, it looks up the B-MAC/I-SID information to determine the
label stack to be added to the frame for forwarding in the EVPN. The
PE strips the B-VID information from the frame, adds the label
information to the frame and forwards the resulting MPLS packet.
5.6. Data plane Interworking EVPN to 802.1aq SPBM island
When a PE receives a packet from the EVPN it may infer the B-VID to
overwrite in the SPBM frame from the I-SID or by other means (such as
via the bottom label in the MPLS stack).
If the frame has a local multicast DA, it overwrites the SPsourceID
in the frame with the local SPsourceID.
5.7. Data plane interworking EVPN to 802.1ah PBB-PE
A PBB-PE actually has no subtending PBBN nor concept of B-VID so no
frame processing is required.
A PBB-PE is required to accept SPBM encoded multicast DAs as if they
were 802.1ah encoded multicast DAs. The only information of interest
being that it is a multicast frame, and the I-SID encoded in the
lower 24 bits.
5.8. Data plane interworking between 802.1Qbp islands and EVPN
For a future version of the document
5.9. Multicast Stitching
For a future version of the document
6. Other Aspects
6.1. Flow Ordering
When per I-SID multicast is implemented via PE replication, a stable
network will preserve frame ordering between known unicast and BU
traffic (e.g. race conditions will not exist). This cannot be
guaranteed when multicast is used in the EVPN.
Allan et al., Expires August 2013 [Page 8]
Internet-Draft draft-allan-l2vpn-spbm-evpn-03 February 2013
6.2. Transit
Any PE that does not need to participate in the tandem calculations
may use the IS-IS overload bit to exclude SPBM tandem paths and
behave as pure interworking platform.
7. Acknowledgements
The authors would like to thank Peter Ashwood-Smith and Janos Farkas
for their detailed review of this draft.
8. Security Considerations
For a future version of this document.
9. IANA Considerations
For a future version of this document.
10. References
10.1. Normative References
[1] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC2119, March 1997.
[2] Fedyk et.al. "IS-IS Extensions Supporting IEEE 802.1aq
Shortest Path Bridging", IETF RFC 6329, April 2012
[3] Rosen et.al., "BGP/MPLS IP Virtual Private Networks
(VPNs)", IETF RFC 4364, February 2006
[4] Aggarwal et.al. "BGP MPLS Based Ethernet VPN", IETF work
in progress, draft-ietf-l2vpn-evpn-01, July 2012
10.2. Informative References
[5] IEEE Standard for Local and Metropolitan Area Networks:
Bridges and Virtual Bridged Local Area Networks -
Amendment 9: Shortest Path Bridging
[6] Draft IEEE Standard for Local and Metropolitan Area
Networks---Virtual Bridged Local Area Networks -
Amendment: Equal Cost Multiple Paths (ECMP), 802.1Qbp
draft 1.0
[7] Sajassi et.al. "PBB E-VPN", IETF work in progress, draft-
ietf-l2vpn-pbb-evpn-03, June 2012
Allan et al., Expires August 2013 [Page 9]
Internet-Draft draft-allan-l2vpn-spbm-evpn-03 February 2013
[8] 802.1Q (2011) IEEE Standard for Local and metropolitan
area networks--Media Access Control (MAC) Bridges and
Virtual Bridged Local Area Networks
11. Authors' Addresses
Dave Allan (editor)
Ericsson
300 Holger Way
San Jose, CA 95134
USA
Email: david.i.allan@ericsson.com
Jeff Tantsura
Ericsson
300 Holger Way
San Jose, CA 95134
Email: jeff.tantsura@ericsson.com
Don Fedyk
Alcatel-Lucent
Groton, MA 01450
USA
EMail: Donald.Fedyk@alcatel-lucent.com
Ali Sajassi
Cisco
170 West Tasman Drive
San Jose, CA 95134, US
Email: sajassi@cisco.com
Allan et al., Expires August 2013 [Page 10]
